Can I Install A Bath Tub Myself?
Can I Install A Bath Tub Myself?
Blog Article
The content down below about A Step-by-Step Guide to Installing a Bathtub is definitely interesting. Read it for your own benefit and see what you think of it.
Setting up a bath tub isn't precisely brain surgery, but it does need solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old tub is easily accessible, the job can relocate rapidly; if you need to open a wall surface to get rid of the old tub and also position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a home handyman's abilities, although you will certainly need an assistant to move out the old tub and also set in the brand-new one. See to it you have certified on your own for the job and also are comfortable attempting it. As opposed to working with a professional to take control of a halfway-completed task, it is better to think about using one prior to you start. Opportunities are you may need an expert plumber to make tube links.
This article will aid you mount a new tub in your restroom if you have currently acquired a new tub as well as do not require to change the arrangement of your previous supply of water pipelines.
Your devices and also material list ought to make up the following:
Preparing for the Installation
First of all, the sustaining framework provided with the bathroom needs to be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of removing the existing faucets can be rather problematic as a result of the limited access that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Using both wooden boards under its feet, place the tub in the required setting. The wood boards are valuable in evenly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and changing the feet on the bath tub until the spirit level reviews level.
To install taps, fit all-time low of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Turn on the water supply as well as inspect all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as also inspect the overflow electrical outlet and also the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub must wait till the bathtub has actually been made use of at least when as this will certainly settle it into its last placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making sure that the washing machines are in place in between the tap and the sink. Protect the faucet in position with the producer supplied backnut. As soon as the tap is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal tap connectors. The former kind should be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack a rigid seal, creating the water to pass through the wall surface between the bath and also the tiling, bring about difficulties with wetness as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealant can crack rather very early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the market. It is a good idea to fit the ceramic tiles making use of waterproof or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid person who reads about A Step-by-Step Guide to Installing a Bathtub, I think sharing that article was really helpful. Kindly take the opportunity to distribute this blog if you enjoyed it. I treasure reading our article about How to Install a Bathtub.
Call Today
Report this page